#RESET SERIAL CLONER UPDATE#
#RESET SERIAL CLONER SOFTWARE#

You can do the following in the Check In C2V dialog box: Click. NOTE If the C2V file contains dynamic memory data, the dynamic memory file is displayed with Base64 encoding in the Content column of the Dynamic Memory tab. You can also generate a file that you can send to a customer to format a key that is already deployed. In addition, it enables you to format a key.

#RESET SERIAL CLONER UPDATE#

This information can be used in connection with Protection Key Update orders. void pulse ( int pin, int times ) #ifdef USE_HARDWARE_SPI #include 'SPI.The Check in C2V dialog box enables you to process and store the Sentinel security key information that is contained in a Customer-to-Vendor (C2V) file. To use 'Serial': #define SERIAL Serial #ifdef SERIAL_PORT_USBVIRTUAL #define SERIAL SERIAL_PORT_USBVIRTUAL #else #define SERIAL Serial #endif // Configure the baud rate: #define BAUDRATEđ9200 // #define BAUDRATEđ15200 // #define BAUDRATEđ000000 #define HWVER 2 #define SWMAJ 1 #define SWMIN 18 // STK Definitions #define STK_OK 0x10 #define STK_FAILED 0x11 #define STK_UNKNOWN 0x12 #define STK_INSYNC 0x14 #define STK_NOSYNC 0x15 #define CRC_EOP 0x20 //ok it is a space.

// On the Due and Zero, 'Serial' can be used too, provided you disable autoreset. Due and Zero have an USB virtual serial port: 'SerialUSB'. // Leonardo and similar have an USB virtual serial port: 'Serial'. - it is more reliable because of USB handshaking. native USB port), if the Arduino has one: // - it does not autoreset (except for the magic baud rate of 1200). // Prefer the USB virtual serial port (aka. We must use pins that are broken out: #else #define RESET 4 #define LED_HB 7 #define LED_ERR 6 #define LED_PMODE 5 #endif // By default, use hardware SPI pins: #ifndef PIN_MOSI #define PIN_MOSI MOSI #endif #ifndef PIN_MISO #define PIN_MISO MISO #endif #ifndef PIN_SCK #define PIN_SCK SCK #endif // Force bitbanged SPI if not using the hardware SPI pins: #if (PIN_MISO != MISO) || (PIN_MOSI != MOSI) || (PIN_SCK != SCK) #undef USE_HARDWARE_SPI #endif // Configure the serial port to use. #define USE_OLD_STYLE_WIRING #ifdef USE_OLD_STYLE_WIRING #define PIN_MOSIđ1 #define PIN_MISOđ2 #define PIN_SCK 13 #endif // HOODLOADER2 means running sketches on the ATmega16U2 serial converter chips // on Uno or Mega boards. #ifndef ARDUINO_HOODLOADER2 #define RESET 10 // Use pin 10 to reset the target rather than SS #define LED_HB 9 #define LED_ERR 8 #define LED_PMODE 7 // Uncomment following line to use the old Uno style wiring // (using pin 11, 12 and 13 instead of the SPI header) on Leonardo, Due. #if defined(ARDUINO_ARCH_AVR) #if SPI_CLOCK > (F_CPU / 128) #define USE_HARDWARE_SPI #endif #endif // Configure which pins to use: // The standard pin configuration. Currently only for AVR, for other architectures (Due, Zero.), hardware SPI // is probably too fast anyway.

#RESET SERIAL CLONER SOFTWARE#

divide target // f_cpu by 6: // #define SPI_CLOCK (128000/6) // // A clock slow enough for an ATtiny85 1 MHz, is a reasonable default: #define SPI_CLOCK (1000000/6) // Select hardware or software SPI, depending on SPI clock. for an ATtiny 128 kHz: the datasheet states that both the high and low // SPI clock pulse must be > 2 CPU cycles, so take 3 cycles i.e. // Put an LED (with resistor) on the following pins: // 9: Heartbeat - shows the programmer is running // 8: Error - Lights up if something goes wrong (use red if that makes sense) // 7: Programming - In communication with the slave // #include 'Arduino.h' #undef SERIAL #define PROG_FLICKER true // Configure SPI clock (in Hz). A simple way to accomplish this is to power the complete system (programmer // and target) at 3V3. ) as // the programmer, make sure to not expose any of the programmer's pins to 5V. // IMPORTANT: When using an Arduino that is not 5V tolerant (Due, Zero. // Alternatively you can use any other digital pin by configuring // software ('BitBanged') SPI and having appropriate defines for PIN_MOSI, // PIN_MISO and PIN_SCK. This will work even when not // using an Uno. If you find this wiring more // practical, have a define USE_OLD_STYLE_WIRING.

That is why many tutorials instruct // you to hook up the target to these pins. GND // // On some Arduinos (Uno.), pins MOSI, MISO and SCK are the same pins as // digital pin 11, 12 and 13, respectively. On all Arduinos, these pins can be found // on the ICSP/SPI header: // // MISO °. // By default, the hardware SPI pins MISO, MOSI and SCK are used to communicate // with the target. ArduinoISP // Copyright (c) 2008-2011 Randall Bohn // If you require a license, see // // // This sketch turns the Arduino into a AVRISP using the following Arduino pins: // // Pin 10 is used to reset the target microcontroller.

Reset serial cloner